Every page from Cameras and Darkroom that made up the original guide, in its original order. Use your browser's print command to make a paper copy.
Part 1Kit and bottles
Film and developing — complete
| Item | Notes |
|---|---|
| Paterson Multi-Reel 3 tank (PTP116) | Holds 3× 35mm or 2× 120 |
| Paterson auto-load reels ×3 | Adjust between 35mm and 120 |
| MOD54 4x5 insert | Not usable for 124 — see the 124 reel |
| Ilford HP5 Plus 400, 120 ×3 | |
| Ilfosol-3 developer, 500 mL | One-shot, 10 rolls’ worth |
| Ilford Rapid Fixer, 1 L | Film and paper, at different dilutions |
| Ilfostop, 500 mL | Film and paper, same dilution |
| Sensei changing bag, 27×30” | Right size for wrestling 120 |
| CineStill accordion bottles, 1 L ×3 | See assignments below |
| Paterson film clip set | Weighted + plain clips; also dries prints |
| 1000 mL glass beaker | Mixing working solution |
| 100 mL glass graduate | Measuring concentrate |
| High-res thermometer |
Printing — ordered or on hand
| Item | Notes |
|---|---|
| Photographers’ Formulary 8×10 contact print frame | Spring back holds curly vintage film flat |
| Paterson 8×10 trays ×3 | Developer, stop, fixer |
| Samigon bamboo tongs ×3 | One per tray, never swapped |
| Ilford Multigrade filter set, 6×6” (12) | Contrast control — see contact printing |
| Ilford Multigrade developer, 500 mL | Paper developer |
| Ilford Multigrade RC Deluxe Pearl, 5×7, 100 sheets | Starter paper |
| Flic Film red LED safelight bulb | Fog-test before use (contact printing) |
| DiCUNO pendant cords with inline switch ×2 | One exposure light, one safelight |
| 25W A19 incandescent, warm white | Exposure light; filter grades behave as labeled |
| Timer | Tape over any lit display (contact printing) |
Bottle assignments
- Film fixer working solution (1+4). Mix 1 L at a time so the bottle starts completely full.
- Stop working solution (1+19), shared by film and paper.
- Ilfosol-3 concentrate, decanted once the original is half gone. Collapse the bottle as the level drops.
- Optional — paper fixer (1+9). Not needed: RC paper can use bottle 1 (1+4) for 30 s (contact printing). Use a separate bottle only if you print a lot.
Multigrade developer concentrate stays in its own bottle. Mix its working solution fresh each printing session.
Still need
- Anti-static brush or air blower
- Scissors — trimming film corners before loading
- Cotton gloves for handling the vintage negatives
A phone is fine as a timer for film developing, which happens in room light. Don’t use it in the printing darkroom, where the screen can fog paper. Use the timer there.
Wetting agent
- Ilfotol, used at 1+200 in RO/DI water for the final rinse (developing, Step 8). Measure it with a 5 or 10 mL syringe, because the amounts are tiny.
Part 2No. 3 Brownie Model 2
The camera is native 124 (3¼ × 4¼). Your spool adapters extend a 120 spool to the 3.716” length the chamber needs — they solve length, not width.
What you get
- 120 film is 61mm wide; the gate is ~83mm. Your frame is 61 × 108mm — a panoramic crop of the native format.
- 6 frames, possibly 7 if you wind tightly. 120 is ~820mm of film and each frame eats ~108mm plus a gap.
- Both the supply spool and the take-up spool need adapters. Four pieces, two per spool.
Orientation — which finder to use
The camera has two finders for two orientations. Orientation does not change the crop. The narrowing always happens across the film’s width, so you get 61 × 108mm either way; holding the camera differently only rotates the frame.
| Held | Result | Good for |
|---|---|---|
| Horizontal | Wide 108 × 61 | Landscapes, groups |
| Vertical | Tall 61 × 108 | Portraits and selfies |
61:108 is almost exactly 16:9, so in vertical orientation you’re shooting a phone-screen aspect ratio on 1910 hardware. For the self-portrait project that’s the thesis built into the geometry. Use the vertical finder.
With actual 124 the frame is 3¼ × 4¼ (about 1:1.31), so vertical gives you 3:4, the classic portrait ratio. Faces still want vertical, but it’s less decisive.
Red window check — do this first
The window is positioned for 124 backing paper. Narrower 120 paper may not cover it.
- Load an empty/sacrificial roll, close the back.
- In bright light, look for any light coming through the window from inside — or shine a flashlight at the window in a dark room and look for leakage past the paper edge.
- If light gets through, tape it over with gaffer or electrical tape. That window is a direct hole to your film.
Winding without the window
Frame numbers won’t align even if the window does land on paper — 120 has three number rows for 6×9, 6×6, and 6×4.5, none matching the No. 3’s spacing.
- Wind by counting turns. Note what you use on roll one and adjust.
- Starting point: wind until you feel the paper leader take up, then count roughly 1½ full turns between frames, decreasing slightly as the take-up roll grows in diameter.
- Log every frame’s wind count in a notebook. Roll one is calibration.
Other prep
- Matte black tape on the bare interior walls beside the gate cuts flare from the extra chamber width.
- Loading and unloading happen in daylight — the backing paper seals the roll. Shade, not direct sun.
- Check the shutter fires on both settings and the lens is free of haze before wasting film.
Developing it
You’re shooting standard 120, so it develops on the reels you already have using the developing recipe exactly as written. No special handling.
Part 3Brownie Hawkeye
620 is the same 61mm film as 120, wound on a thinner spool. It loads (loading the tank) and develops (the developing recipe) exactly like 120. Keep the take-up spool — the camera needs it for the next roll.
| Hawkeye fact | Value |
|---|---|
| Frame | 6×6, 12 per roll, about 2½” apart on the negative |
| Aperture / normal shutter | About f/15 / about 1/40 s (normal setting not yet confirmed on film) |
| B | Open as long as the button is held. For long exposures, clamp the button down and use a card over the lens as the shutter. |
| Focus | Fixed, about 5 ft to infinity |
| Loading | Colored side of the paper up, over the square opening. Wind to “1” in the red window. Tape over the window during long exposures. |
Respooling 120 onto 620 (in the dark bag)
Fresh film like HP5 is sold only in 120. A 120 spool is too large for the Hawkeye, so move the film onto 620 spools. You need two empty 620 spools (an original or your 3D-printed one).
- In the bag: break the seal and wind the whole roll, paper and film together, from the 120 spool onto 620 spool A. Keep it tight and hold it by the edges.
- Wind it again from spool A onto 620 spool B. The second pass puts the leader back on the outside, the right way round.
- Tape the end of the paper down, and only then take it out of the bag.
Practice once in daylight with a dead roll first.
Part 4Exposure and technique
The controls
Three aperture holes, roughly f/11 (large), f/16 (medium), f/22 (small). On “Instant” the shutter is fixed at about 1/40 sec. Those are all the controls you have.
The overexposure problem
This camera was built for ISO 25–50 film. HP5 at 400 is about three stops faster than anything that existed when it was made. Even the smallest hole is roughly two stops over in bright sun.
| Light | Hole |
|---|---|
| Bright sun | Small — always |
| Overcast / hazy | Small or medium |
| Open shade | Medium |
| Deep shade, indoors | Large, or use Time |
HP5 handles overexposure well, so this is workable rather than fatal. If a whole roll was shot in sun, cut development to about 5:30 (the developing recipe).
These are HP5 settings. The vintage rolls are the opposite — see the vintage 124 rolls.
Instant vs. Time
Counterintuitive but important: Instant is the fast setting. Time is slow.
| Setting | Action | Roughly |
|---|---|---|
| Instant | One press | ~1/40 sec |
| Time, quick pull-pull | Pull open, pull closed immediately | ~1/4 sec |
| Time, held open | Pull, wait, pull | Seconds |
A quick pull-pull gives about three stops more exposure than Instant. Use it for slow or aged film in daylight, not only for dim interiors.
Time your own pull-pull. Fire it ten times against a stopwatch and average the results. People land anywhere from 1/8 to 1/2 second depending on their rhythm, and knowing your number lets you plan exposures. Write it in the front of your notebook.
Anything on Time needs the camera braced. A quarter second handheld shows shake.
Focus
Fixed-focus meniscus lens. Sharp from roughly 6–8 feet to infinity. Nothing closer will resolve. There is no focusing mechanism to adjust.
Framing
The finder shows a small, laterally reversed image with significant parallax offset from the taking lens. Frame loose. What you see is approximate at best.
Part 5Self-portrait project
The obstacle is the 6–8 foot minimum focus. Three approaches:
Mirror method (best)
Photograph yourself in a mirror. The focus distance is camera-to-mirror plus mirror-to-you, so you clear the minimum easily while still looking into the lens. The image comes out laterally reversed, which matches the face you see every day. It’s period-appropriate and visually striking.
Time exposure
- Camera on a table or tripod, indoor window light.
- Aperture depends on the film: smallest hole with HP5 (~half second at ISO 400), large hole with the vintage rolls — see the vintage 124 rolls.
- Pull to open, sit still and count “one-one-thousand,” pull to close.
- Sit for it like it’s 1905. Motion blur is the enemy and also the aesthetic.
String release
This camera has no self-timer. Tie thread to the shutter lever, sit 8+ feet away, and pull gently along the lever’s direction of travel. It’s crude but it works.
Worth exploiting
- No double-exposure lockout. You can deliberately fire the shutter without winding, so ghosted and layered self-portraits cost nothing extra. That fits this project well.
- 6 frames a roll means planning matters. Shoot the first two as exposure tests, develop, then commit the rest.
- Shoot vertical. 61 × 108mm is essentially 16:9 — a phone-screen frame from a 1910 box camera. See shooting 120 in the No. 3.
Part 6The two vintage 124 rolls
These are unused stock, not found film, and you’re shooting them yourself. This is the heart of the project: modern self-portraits on film made before your parents were born.
What this changes
- Native format. These are on 124 spools already. No adapters, no 61mm panoramic crop — you get the full 3¼ × 4¼ frame the camera was built for.
- You must develop them yourself, because no lab handles 124. The printed reel is required.
- Six frames per roll, so twelve exposures total, ever. Plan accordingly.
The two rolls, identified
1960 — Kodak Verichrome Pan, 124, 6 exposures, safety film, “develop before September 1960”
- Panchromatic. Total darkness for loading and developing. Changing bag, no exceptions.
- ISO 125 new. Assume ISO 8–25 now.
- This is the best stock you could have. Verichrome Pan turns up again and again in successful recoveries of found film decades past its date, because it ages better than almost anything else from its era.
1948 — Ansco Plenachrome F6, 124
- Black and white orthochromatic. If a listing or box description says “color transparency,” that’s wrong — Plenachrome was Ansco’s ortho B&W roll film. Do not process it as color.
- ASA 25–50 new. Assume ISO 3–12 now. This is very slow film.
- Red-blind, so you can work under a dark red safelight. Being able to watch while you load an 83mm printed reel is a big practical advantage, so use it.
- The ortho look is the point. Lips and skin blemishes render dark, blue eyes pale, skies blank white. It’s how faces looked in 1890s portraiture, which against a modern selfie subject is the whole idea.
Exposure — this inverts the HP5 guidance
Both rolls want the large hole. The small and medium apertures are effectively unusable at these speeds. The real variable is shutter mode (see Instant vs. Time for the speeds).
| Roll | Bright sun | Shade / indoors |
|---|---|---|
| Verichrome Pan (ISO 8–25) | Instant (~1/40) — roughly right, slightly over | Time, quick pull-pull |
| Plenachrome (ISO 3–12) | Time, quick pull-pull (~1/4 sec) | Time, held open 1–2 sec |
The Plenachrome is slow enough that Instant underexposes it even in full sun. Correct exposure at f/11 is near 1/12 second, so 1/40 leaves you a stop or more short. A quick pull-pull overshoots slightly, and over is the right direction to miss with 78-year-old film.
Overexpose both on purpose. Old film loses its shadows to fog first, so err a stop over and never under.
Anything on Time means the camera is braced — table, tripod, fence post. That suits the self-portrait work anyway, since you’re using a string or a mirror.
Do not confuse these with the HP5 table on the exposure page — the guidance is opposite.
Order of operations
- Shoot HP5 first until your process is boring. Several rolls.
- Print and test the 83mm reel (the 124 reel) on sacrificial strips cut to width. Check the mechanical fit with card stock first.
- Shoot the Verichrome Pan first. It’s younger and faster with better odds, and it calibrates you for the Plenachrome.
- Bracket within the roll: with six frames, shoot the same subject twice at different exposures where light allows.
- Develop it and learn from it, then commit the Plenachrome. You’ll develop that one under safelight, which by then you’ll appreciate.
Development
Do not use the times in the developing recipe. Old emulsions need fog control:
- Antifoggant. Add benzotriazole or potassium bromide to the developer. It’s the difference between an image and grey mud.
- Low temperature, long time, minimal agitation. Rodinal 1:100 stand-developed an hour at 68°F is the standard amateur approach for aged stock.
- The Plenachrome can be developed under red safelight, so you can watch density come up in the tray or open tank and pull it when it looks right. That beats developing blind.
- Extended fixing. Old emulsions clear slowly. Do a clip test, then fix for twice the clear time.
- Expect visible base fog regardless. It prints through with longer exposure and a harder filter grade (contact printing), or you can scan and adjust in post. A dense negative still holds an image.
Storage until then
Cool, dry, dark, sealed. Refrigerator is fine. Don’t unroll to inspect — the paper is the only light seal, and these are unrepeatable.
Part 7Loading the tank: 120 and 620
What happens in the dark vs. the light
The changing bag is used for one step only: getting film onto the reel and into the sealed tank. Once the lid is locked, the tank is light-tight and everything else happens at the sink in normal room light.
Into the bag: film roll, dry reel, center column, tank body, tank lid, scissors.
In the dark: separate film from backing paper → load reel → reel onto column → column into tank → black outer lid on and locked.
Out of the bag: the sealed tank, scraps, scissors.
A red safelight is not safe for this step. HP5 and Verichrome Pan are panchromatic, which means they’re sensitive to red light. Load them in total darkness or in the bag. A red safelight is only for paper and for the ortho Plenachrome (the vintage 124 rolls).
Lid anatomy
- Black outer lid — the light seal. Locks on before the bag opens, comes off only after fixing.
- Red center cap — pops out to pour chemistry in and out. Keep it seated during inversions or developer goes across the room.
Loading procedure Total darkness (changing bag)
Practice with a sacrificial roll in daylight first, and expect to sacrifice that roll learning with the lights on.
- Reels must be bone dry. A damp reel jams the film halfway, and you can’t fix that blind. Dry reels overnight or with a hairdryer on cool.
- Set the reel width to 120 — twist the two halves in opposite directions and pull apart until they click at the wide setting.
- In the changing bag: break the seal, unroll. The film is taped to the backing paper at the far end.
- Separate film from paper as you go. Film curls emulsion side in (the dull side faces in).
- Trim the leading corners slightly rounded with scissors. Square corners snag. Save the trimmed corners in a small jar. They’re your clip-test scraps.
- Feed into the ball-bearing entry, then walk the reel halves back and forth to ratchet the film in.
- When you reach the tape, peel or cut it off and finish winding.
- Reel onto column, column into tank, lid on and locked before the bag opens.
If it binds, don’t force it. Back the film out a few inches and re-feed.
620: it’s the same film as 120 on a thinner spool, so load it exactly the same way. The spool never goes in the tank; set it aside for the camera.
Part 8Developing a roll: HP5 Plus in Ilfosol-3
Room light Start here once the film is on the reel and the black lid is locked (loading the tank). Everything below happens at the sink in room light, and the lid stays on until the fixer is out. These steps are for HP5 Plus in Ilfosol-3. For the vintage 124 rolls, follow the vintage 124 rolls instead.
Equipment at the sink
- Loaded tank, plus the red cap
- Tub or sink of 68°F water as a temperature bath
- Thermometer
- 1000 mL beaker (working developer) and 100 mL graduate (concentrate)
- Bottle 1 (film fixer 1+4) and bottle 2 (stop 1+19)
- Ilfosol-3 concentrate
- RO/DI water, about 2 L
- Timer (a phone is fine because the film is sealed)
- Ilfotol and a 5 or 10 mL syringe
- Film clips (weighted + plain), notebook, paper towels
Step 1 — Temper (10–15 min)
- Fill the tub with 68°F (20°C) water.
- Stand the stop and fixer bottles, the loaded tank, and a jug of RO/DI mixing water in it.
- Get everything that touches the film to within 5°F of the developer. Big swings cause reticulation, a crazed pattern in the emulsion.
Step 2 — Mix
| Solution | 1 roll (600 mL) | 2 rolls (1000 mL) | Keep? |
|---|---|---|---|
| Developer Ilfosol-3 1+9 |
60 mL + 540 mL water | 100 mL + 900 mL water | No. One-shot, mix it last |
| Stop Ilfostop 1+19 (bottle 2) |
Pour 600 mL from bottle | Pour 1000 mL | Yes, until it turns purple |
| Fixer Rapid Fixer 1+4 (bottle 1) |
Pour 600 mL from bottle | Pour 1000 mL | Yes, about 24 rolls per liter |
Filling empty bottles: stop is 50 mL Ilfostop + 950 mL water into bottle 2. Fixer is 200 mL Rapid Fixer + 800 mL water into bottle 1. Label each one with the date and a roll tally.
Which water: mix all three solutions with RO/DI. Softened tap water would work, but it swaps calcium for sodium and its mineral content varies, while RO/DI gives the same result every time. Use softened tap water for the wash (Step 7) and RO/DI for the final rinse (Step 8). Draw the RO/DI ahead of time, because it usually comes out cold and needs to sit in the bath.
600 mL covers one 120 reel in the Multi-Reel 3 with margin. Check this once with water and an empty reel, then write the fill volume on the tank in Sharpie.
⚠ Fixer clip test — before every film roll
Bottle 1 fixes both film and prints, so check it’s still strong before you trust a roll to it.
- Pour a little fixer from bottle 1 into a cup at room temperature.
- Drop in a scrap of unprocessed film, such as a corner you trimmed while loading the reel. Developed film won’t work, because it has already been fixed. Light doesn’t matter for this test.
- Time how long the milky scrap takes to turn completely clear.
| Clear time | What to do |
|---|---|
| About 30 s | Fixer is good. Fix film for the normal 3 min, or twice the clear time if that’s longer. |
| About 60 s or more | Fixer is exhausted. Mix a fresh liter (200 mL concentrate + 800 mL water) before you develop. |
Pour the cup back into the bottle, or down the drain if it’s only a splash.
Step 3 — Set the time
Take the developer’s temperature right before you pour, then read off the time.
| 66°F | 67°F | 68°F | 69°F | 70°F | 72°F |
|---|---|---|---|---|---|
| 7:15 | 6:50 | 6:30 | 6:15 | 6:00 | 5:30 |
If the whole roll was shot in bright sun, take about a minute off (~5:30 at 68°F). Box cameras run HP5 about 2–3 stops over in sun.
HP5 at other speeds (Ilford box, 68°F)
| Shot at | Ilfosol-3 1+9 | Ilfosol-3 1+14 | Use |
|---|---|---|---|
| EI 200 | 5:00 | 7:00 | Bright sun in box cameras (overexposed roll) |
| EI 400 | 6:30 | 11:00 | Normal |
| EI 800 | 13:30 | 19:30 | Dim light, such as arenas (push 1 stop) |
| EI 1600+ | Not listed for Ilfosol-3. Use Ilfotec DD-X (1+4: 13:00 at 1600, 20:00 at 3200) | Pushing 2+ stops | |
Ilford’s box also gives ranges for stop (10–30 s) and fix (2–5 min), and calls for continuous agitation for the first 10 s, then 10 s every minute.
Other films in this recipe
| Film | Developer mix (600 mL) | Time at 68°F | Changes |
|---|---|---|---|
| Kodak Verichrome Pan 620/120, 1970s expired | Ilfosol-3 1+14: 40 mL + 560 mL RO/DI | 7:30 (confirmed on a good roll) | Fix 5 min. Extending to 12 min didn’t rescue a dead roll. Pink dye in the first wash is normal. |
Verichrome Pan is roughly Plus-X emulsion on a roll-film base, and it holds up well with age. Users report that decades-old rolls develop at about the normal time. Kodak never published an Ilfosol-3 time, so 7:30 at 1+14 is an estimate. The more dilute developer keeps the time above 5 minutes, below which Kodak warns development can be uneven. Write down what you get.
Verichrome log (Nov 2026)
| Roll | Result | Cause |
|---|---|---|
| 1 | Opaque gray, no edge print | Loaded under red safelight, which fogged the panchromatic film |
| 2, 3 | Cloudy, mottled gray. Edge print visible, no frames | Dead film: heavy age fog and almost no sensitivity left. The fog sits in the gaps and edges too, which rules out the camera. |
| 4 | Good images, clear gaps | Lamp-lit still life on B. About 1–2 s was best; 8 s and longer came out too dense. |
Old rolls vary by batch and by how they were stored. Note the date and lot number on each box, and match them to your results.
Step 4 — Develop
- Pull the red cap. Start the timer and pour the developer in steadily through the funnel. Cap it.
- First 30 s: slow, continuous inversions. Then tap the tank firmly on the counter to knock loose air bubbles.
- Top of every minute: 4 slow inversions (about 10 s), then tap. Between cycles, set the tank back in the bath.
- 10 s before the end: pull the cap and start pouring the developer out.
Keep inversions smooth and don’t shake. Shaking causes surge marks along the edges, and skipping the tap leaves bubble spots.
Step 5 — Stop (10 s)
- Pour in the stop and agitate continuously for 10 s.
- Pour it back into bottle 2.
Step 6 — Fix (3 min)
- Pour in the fixer. Agitate continuously for the first 30 s, then do 4 inversions each minute.
- At 3:00, pour it back into bottle 1. Squeeze the air out of the accordion bottle and add a tally mark.
- The film is now safe from light, so the lid can come off.
Step 7 — Wash (Ilford method, ~5 min)
Use softened tap water within 5°F of the developer, and dump each fill when you finish its inversions.
- Fill, 5 inversions, dump.
- Fill, 10 inversions, dump.
- Fill, 20 inversions, dump.
Step 8 — Final rinse (RO/DI, then Ilfotol)
-
RO/DI rinse: fill with RO/DI water, do a few gentle inversions, and dump. This clears the hard-water minerals left from the wash.
-
Mix the Ilfotol rinse (1+200) in the beaker. Use RO/DI water, and add the Ilfotol after the water so it doesn’t foam.
Rinse volume Ilfotol RO/DI water 600 mL (1 roll) 3 mL 597 mL 1000 mL (2 rolls) 5 mL 995 mL Stir gently. Bubbles mean you stirred too hard.
-
Soak, 30 s: pour it in and give it one or two very slow inversions, or just turn the reel by its center column. Vigorous agitation makes foam, and foam leaves marks.
-
Dump it. Use it once and drain it. Don’t rinse afterward. The thin layer of Ilfotol is what lets the water sheet off evenly.
-
Hang the film straight from the reel (Step 9). With Ilfotol, you can skip the finger squeegee or do it very lightly. Water runs off on its own.
Reel care: Ilfotol residue can make auto-load reels sticky. Rinse the reels well in warm water and dry them completely before the next load.
Step 9 — Hang to dry (2–3 h)
- Unwind the film from the reel, holding it by the edges.
- Clip the top in a dust-free spot (the shower stall with the door closed works), and hang a weighted clip on the bottom.
- Squeegee with your fingers only. A rubber squeegee drags grit across the emulsion.
- Leave it alone until it’s dry, then cut it into strips and sleeve it. From here on, every scratch and speck shows up in the print.
Step 10 — Clean up
| Item | What to do |
|---|---|
| Used developer | Down the drain with running water |
| Stop | Already back in bottle 2. Replace it when the indicator turns purple |
| Fixer | Already back in bottle 1. Clip-test it as you approach 24 rolls (chemistry lifespan). Never pour used fixer down the drain — it carries silver. Take exhausted fixer to household hazardous waste |
| Tank, lid, column, reels | Rinse in warm water. Dry the reels completely (overnight, or a hairdryer on cool) before the next load |
| Beaker, graduate, thermometer | Rinse. Developer residue stains, so wipe up spills now |
| Notebook | Record the film, camera, developer temperature, time, agitation, and anything odd |
Cheat card
Print this and tape it inside a cabinet door.
| Step | Solution | Time | After |
|---|---|---|---|
| Develop | Ilfosol-3 1+9, 68°F | 6:30 | Drain |
| Stop | Ilfostop 1+19 | 10 s | Bottle 2 |
| Fix | Rapid Fixer 1+4 | 3 min | Bottle 1 |
| Wash | Water, 5 / 10 / 20 inversions | ~5 min | Dump |
| Rinse | RO/DI, gentle inversions | ~30 s | Dump |
| Wetting agent | Ilfotol 1+200 in RO/DI (3 mL in 600 mL) | 30 s, 1–2 slow inversions | Drain, no rinse |
| Dry | Hang, weighted clip | 2–3 h | Sleeve |
Part 9The 124 reel project
You have unexposed 124 film, and no lab processes it, so this reel is the only way to develop those two rolls. Build and test it well before you shoot them.
- 124 film is ~83mm wide (3¼ × 4¼ image), discontinued 1961.
- The MOD54 won’t work. It’s a cage for six 4x5 sheets, not a continuous spiral, and a 124 roll is one strip about 26 inches long.
- The path is a 3D-printed reel in the Multi-Reel 3 body, which has the internal height to clear an 83mm reel.
- Start with the 101/122 reel for Paterson 3-reel tanks on Printables. 122 film is the same width as 124, so it should fit directly.
- Backup: Atech’s parametric Paterson-compatible reel set, also on Printables. It includes STEP files, so you can adjust the width yourself.
Print notes
- Opaque filament only. Natural PLA and translucent colors light-pipe and will fog your film.
- Black PETG over PLA — PLA softens around 130°F, and warm developer gets closer to that than you’d like.
- Open the film groove 0.1–0.2mm past nominal. Old film is curled and brittle.
- Dry-fit with a scrap strip cut to width before you trust a real roll in the dark.
Before printing: measure your actual film. 124 used a 3.716” spool vs 118’s 3.474”, so spool length varied even at the same film width.
Part 10Negative troubleshooting
| What you see | Cause |
|---|---|
| Thin, weak negatives | Underdeveloped, temp too low, or underexposed |
| Dense, blocked highlights | Overdeveloped or temp too high |
| Clear circular spots | Air bubbles — tap the tank after agitating |
| Overall grey fog | Light leak in the bag, or the film is old |
| Streaks off the frame edges | Over-agitation |
| Crazed surface texture | Big temperature swing between steps |
| Nothing at all on the film | Fixer used before developer, or camera issue |
| Clear film with edge markings visible | Camera problem, not developing — the film never got exposed |
| Uniform cloudy gray, edge markings visible, no frame borders, and gaps as gray as the frames | Dead old film (age fog plus lost sensitivity). The camera can’t put density in the gaps, so this is the film. |
| Dense gray over the whole roll, no edge markings | Fogged during loading, for example under a safelight with panchromatic film |
Quick diagnosis: edge markings visible means development worked. Gaps clear means the film itself is fine, so look at exposure. Gaps cloudy means the film is fogged.
Look at negatives against a window before you judge anything. Dense-looking negatives often print or scan fine.
Part 11Contact printing
Contact printing lays the negatives directly on paper under glass and exposes them to light. Each print is the same size as its negative. Use this section for a contact sheet of a whole roll, or for a single print of one frame. Paper is Ilford Multigrade RC Deluxe 5×7, and the whole process happens in the basement bathroom under the safelight.
Equipment
- Contact print frame, glass cleaned
- Three trays, always in the same order left to right: white = developer → red = stop → grey = fixer (“red means stop”). Under the safelight the red tray looks almost white, so trust the position and mark each rim with tape (D, S, F). One pair of tongs per tray, marked the same way, never swapped.
- Multigrade developer concentrate, bottle 2 (stop 1+19), bottle 1 (fixer 1+4)
- 1000 mL beaker and 100 mL graduate, thermometer
- 25W exposure bulb 3–4 ft above the frame, safelight at least 4 ft away, timer with its display taped over
- Paper box, scissors, a piece of black cardboard for test strips, Multigrade filters and their holder
- Blower or anti-static brush, cotton gloves
- Sink or tub of water as the holding bath, clips to hang prints, pencil, notebook
Which light, when
| Light | When | Paper box |
|---|---|---|
| Room light | Setup, judging test strips, washing, cleanup | Closed |
| Safelight only | Cutting paper, loading the frame, developing and fixing | May be open |
| Bulb for exposure only | Only during the timed exposure, with the safelight still on | Closed |
Rule: before the room light goes on, the paper box is closed and every sheet is either in the fixer or finished.
What has worked (Nov 2026)
- Safelight: the Flic 5W LED fogged paper to mid-gray in about 40 s in the bathroom. Until it passes a 5-minute coin test, work in total darkness, with an audible timer and fixed spots for everything.
- Proof sheet (pushed HP5): 1W amber LED at 3–4 ft, no filter, 1 s.
- Best recipe so far, 4W incandescent night-light bulb (E12 adapter) at 3–4 ft, pushed HP5 basketball roll:
- Proof sheet: no filter, about 4 s.
- Prints: grade 3, about 12 s (best tones). 16 s was too dark and 4–8 s too light. Try 10 s for slightly lighter faces.
- Grade 5 barely prints with this bulb, because its warm light has too little blue. Use the 25W bulb for grades 4–5.
- High-contrast recipe (favorite): 25W bulb at 3–4 ft, one sheet of printer paper hung 4–6” below it as a diffuser, grade 5, 6 clicks (switch on and off with a steady rhythm). 5 clicks is lighter in the faces and 7 is too dark. Clicks only stay valid with the same bulb, diffuser spacing and rhythm.
- 25W bare, grade 5: 4 s is far too dark. These negatives need about 1–2 s, which is too short to time well, so dim the bulb if you want grade 5.
- 8W LED + grade 5: washed out and flat. Avoid LEDs with the high-grade filters.
- Single prints: 25W incandescent at 3–4 ft with a thin white cotton glove over it, grade 5 filter, about 5 s. Strong blacks, clean whites. 2 s came out far too light.
- ⚠ Don’t repeat the glove on an incandescent bulb. It can scorch. To get the same dimming safely, tape 1–2 sheets of printer paper over the box window instead, then re-test grade 5 at 2, 4, 8 and 16 s.
- Under incandescent light the filters follow Ilford’s rule: grades 0–3½ need about half the grade 5 time (about 2–3 s in this setup).
Before the first session only
- Dark check Total darkness. With the room light and the safelight both off, wait 3–5 minutes. Tape over anything that glows: GFCI light, fan switch, smoke detector LED, timer display, the switches on the pendant cords, light under the door.
- Safelight fog test Safelight only. With the safelight on, lay a sheet of paper where the trays sit and put a coin on it for 5 minutes. Develop and fix the sheet. If any outline of the coin shows, move the safelight farther away.
Step 1 — Clean and arrange the negatives Room light
- Put on cotton gloves. Hold the negatives by their edges.
- Blow dust off both sides, and wipe both sides of the frame glass.
- Plan the layout. A 5×7 sheet holds two rows of Hawkeye 6×6 frames. Three frames in a strip measure about 7.1”, slightly longer than the paper’s 7”, so the outer edges of the end frames may get trimmed a little. For a proof sheet that’s fine. Loose frames can be butted closer together, so three of them fit with room to spare.
- Sort each sheet’s negatives before the lights go off. For 12 Hawkeye frames, use sheet A for two 3-frame strips and sheet B for one 3-frame strip plus three loose frames.
Step 2 — Mix the trays (68°F, about 500 mL each) Room light
| Tray | Mix | Time | Keep? |
|---|---|---|---|
| 1. Developer Multigrade 1+9 |
50 mL concentrate + 450 mL water | 60 s | No. Discard at end of session |
| 2. Stop Ilfostop 1+19 |
Pour 500 mL from bottle 2 | 10 s | Yes, back to bottle 2 until it turns purple |
| 3. Fixer Rapid Fixer 1+4 (bottle 1, shared with film) |
Pour 500 mL from bottle 1 | 30 s | Yes, back to bottle 1 |
One fixer for both: Ilford rates Rapid Fixer at 1+4 for RC paper at 30 s, so the film bottle works for paper too. Prints use up its capacity, so clip-test it before each film roll (the clip-test box).
Mix with RO/DI water. Fill the sink or tub with water as a holding bath, then turn the exhaust fan on.
Step 3 — Set up the light Room light
- Hang the bulb 3–4 ft above the frame. Mark the height so it’s the same every session.
- Filter (optional): with no filter, Multigrade paper under a warm incandescent bulb prints at about grade 2, so start without one. Add a filter only when a test strip shows you need more or less contrast.
- Filter stand, if you need one: cut a window in a piece of stiff cardboard and tape the filter over it. Rest the cardboard on two stacks of books so it sits 3–6” above the frame. At that height, dust on the filter is out of focus. Never lay a filter directly on the frame glass, because its dust and scratches will print.
- Times change with a filter. Filters absorb light, so expect longer exposures than without one. Make a new test strip whenever you add or change a filter.
- Switch: room light OFF, safelight ON. Close the door. From here, the paper box only opens under the safelight.
Step 4 — Test strip Safelight only Bulb for exposure only
-
Cut one 5×7 sheet lengthwise into four strips about 1¼” × 7”. Put three back in the box and close it.
-
Load the frame face down on the table, in this order (see the diagram):
- Glass in the frame.
- Negatives on the glass. Their shiny side touches the glass, and their dull side faces up. The dull side is the emulsion.
- Paper on top of the negatives. Its shiny side faces down, touching the negatives’ dull side. On paper, the shiny side is the emulsion. For a test strip, lay it across faces or midtones, crossing several frames if you can.
- Spring back on last, then close it.
The rule to remember: emulsion faces emulsion, meaning the film’s dull side touches the paper’s shiny side.
-
Close the spring back and turn the frame over. The edge printing should read correctly through the glass.
-
Cover all but one section of the strip with the black card. Turn the bulb on for the step time, turn it off, uncover the next section, and repeat across the strip. Keep the safelight on throughout.
| Negatives | Step | Bands get | Filter |
|---|---|---|---|
| HP5, normal density | 3 s | 3, 6, 9, 12, 15, 18 s | Grade 2 |
| Thin negatives (pushed or underexposed, like the basketball roll) | 2 s | 2, 4, 6, 8, 10, 12 s | Grade 3 |
| Vintage or fogged negatives | 5 s | 5, 10, 15, 20, 25, 30 s | Grade 3½–4 |
- Process the strip under the safelight (developer, stop, fixer as in Step 6).
- Close the paper box. Then switch the room light on and judge the strip.
Step 5 — Read the test strip Room light
- Time sets the highlights. Pick the band where whites and skin show detail but aren’t gray.
- The filter sets contrast. If the highlights look right but the shadows are muddy, go up a grade. If the shadows are blocked or the print is harsh, go down a grade.
- If the best band is under 5 s, raise the bulb. If it’s over 30 s, lower the bulb. After any height or grade change of more than about one grade, make a new test strip.
- RC paper dries a little darker, so pick a band that looks slightly light.
- Switch back: room light OFF, safelight ON before you open the paper box.
Step 6 — Expose and process Safelight only Bulb for exposure only
- Load a full sheet the same way. Turn the bulb on for the chosen time, then off.
- Developer, 60 s. Slide the paper in quickly, face up, and rock the tray the whole time. The image appears at about 10–15 s, but always give the full minute. Drain for 5 s.
- Stop, 10 s. Rock, then drain for 5 s.
- Fixer, 30 s (at 1+4). Rock. Don’t go past about 1 minute, because longer fixing bleaches RC paper.
- Put the print in the holding bath. Repeat Step 6 for the next sheet.
- When the last print is out of the fixer, close the paper box, and only then turn the room light on.
- In pencil on the back, write the time, grade and bulb height.
Step 7 — Wash and dry Room light
- Wash all prints together for 2 minutes in running water, or in 3–4 changes of water.
- Hang them by a corner with the film clips, or lay them face up on a screen. RC paper dries in about 15–30 minutes.
Step 8 — Clean up Room light
| Item | What to do |
|---|---|
| Paper developer | Down the drain |
| Stop | Back to bottle 2 if it’s still yellow |
| Fixer | Back to bottle 1. Tally the sheets on the label next to the roll count. When it’s exhausted, take it to household hazardous waste rather than the drain. |
| Trays and tongs | Rinse in warm water and stand them up to dry. Keep each tray in its developer, stop or fixer position next time. |
| Frame and negatives | Wipe the glass, and sleeve the negatives again |
| Notebook | Roll, sheet, time, grade and bulb height for each print |
Cheat card
| Step | Solution | Time | After |
|---|---|---|---|
| Expose | 25W bulb, 3–4 ft, no filter (about grade 2) | From the test strip | — |
| Develop | Multigrade 1+9, 68°F | 60 s | Drain |
| Stop | Ilfostop 1+19 | 10 s | Bottle 2 |
| Fix | Rapid Fixer 1+4 (bottle 1) | 30 s | Bottle 1 |
| Wash | Running water | 2 min | — |
| Dry | Hang or lay flat | 15–30 min | Label |
Cleaning negatives
- Dust: use a blower or anti-static brush before every print. Dust prints as white specks.
- Fingerprints: soak the negatives in RO/DI water with a drop of wetting agent (Ilfotol) for 5 minutes, swish them, then hang to dry as after developing. A dedicated film cleaner such as PEC-12 with PEC*PAD wipes also works. Never rub a dry negative with cloth.
- Oils left on for weeks can etch the emulsion permanently, so clean fingerprints soon. From now on, handle negatives only by the edges or with cotton gloves.
Your negatives
- HP5: straightforward. Start at grade 2.
- Pushed HP5 (basketball): thin negatives, so expect short times. Start at grade 3.
- Vintage 124 or Verichrome: fog adds density and lowers contrast, so expect longer times and grade 3½–5. The spring back flattens curl.
- Soft negatives stay soft at any grade. A higher grade adds snap, not sharpness.
- Cyanotype later uses the same frame and loading, but needs UV light (sun or a UV panel), not this bulb.
Print troubleshooting
| Symptom | Likely cause | Fix |
|---|---|---|
| Whole print gray, including borders | Light leak or safelight fog | Redo the dark check and safelight test |
| Print mirror-reversed | Negative upside down | Emulsion faces emulsion |
| Soft or blurry | Negative not flat, or upside down | Check spring back and orientation |
| White specks | Dust on negative or glass | Blow off both before every print |
| Smudgy patches | Fingerprints | Clean the negatives (above) |
| Black specks or lines | Scratches in the negative | Retouch the dry print |
| Too dark overall | Too much exposure | Shorter time, or raise the bulb |
| Flat and gray, whites dull | Too little contrast | Higher filter grade |
| Harsh, blocked shadows | Too much contrast | Lower filter grade |
| Uneven or blotchy development | No agitation, or paper not fully submerged | Slide paper in quickly and rock continuously |
| Brown or yellow stains later | Exhausted fixer or poor washing | Fresh paper fixer; wash the full 2 minutes |
| Exposure times drift between sessions | Bulb height or bulb changed | Keep height fixed; make a new test strip after any change |
Part 12Chemistry lifespan
| Chemical | Used for | Reuse? | Life |
|---|---|---|---|
| Ilfosol-3 working | Film | No — one-shot | Discard immediately |
| Ilfosol-3 concentrate | Film | — | Months once opened. Decant into smaller bottles as it depletes. |
| Multigrade developer working | Paper | No | Discard at the end of each session, or sooner if it browns or prints get slow and flat |
| Multigrade developer concentrate | Paper | — | Keep capped; months once opened |
| Ilfostop working (bottle 2) | Both | Yes | Until the indicator turns purple |
| Rapid Fixer 1+4 (bottle 1) | Film and RC paper | Yes | About 24 rolls per liter for film alone. Prints share that capacity, so clip-test it before each film roll. |
| Rapid Fixer concentrate | Both | — | Years sealed |
Mixing fixer, one liter at a time:
- Film (1+4): 200 mL concentrate + 800 mL water
Label each bottle with the date and a tally of rolls and prints. If you ever keep a separate paper fixer at 1+9, never pour it into bottle 1.
Fixer clip test: see the clip-test box. Do it before every film roll.
Three rolls of HP5 use about 180 mL of Ilfosol-3 at 60 mL a roll, and barely touch the stop and fixer.
Part 13Session checklists
First developing session
- Shoot one roll. Don’t shoot all three before you develop one.
- Practice-load a sacrificial roll in the light.
- Load for real in the changing bag (loading the tank).
- Clip-test the fixer (clip test).
- Run the developing recipe top to bottom, including cleanup.
- Look at the negatives against a window before you judge anything.
Each time, write down what you did: temperature, times, agitation. Notes from three rolls are worth more than any guide.
Printing session
- Choose and clean the negatives, and plan the layout for each sheet.
- Run the contact printing recipe from top to bottom, including cleanup.
- Log time, grade and bulb height for every print.
Part 14Enlarging (on hold)
For prints larger than the negative. Parked for now; notes so far:
What your negatives need
- 124 is 83 × 108mm and the 120 panoramic frame is 61 × 108mm. Both need a 4x5-class enlarger.
- Enlargers that top out at 6x9 or 6x7 can’t take the 124 frames, and they crop the 108mm length of the panoramic frames to about 84mm or 69mm. That rules out the Intrepid Compact, Beseler 23C, Omega B-22, and Rolleimat Universal for this project.
- Good candidates: Beseler 45 series (45MX, 45MXT), Omega D2 / D5, Durst Laborator 138. Beseler 45M parts interchange back to 1953.
- Light source: diffusion, cold light, or dichroic color head preferred. Diffuse light hides dust and scratches on old negatives; a color head’s dials double as multigrade filtration.
- Lens: 135mm or 150mm covers both formats.
- Carrier: one 4x5 carrier, masked with tape, handles both 120 and 124, so no 6x9 carrier is needed. A glass carrier masked to 83 × 108mm also works. Carriers sold for “124 Instamatic” are for 126 cartridge film and won’t fit.
Print size (150mm lens, 124 negative)
| Magnification | Negative-to-paper | At home | |
|---|---|---|---|
| 8×10 | ~2.4× | ~28” | Easy — the sweet spot |
| 11×14 | ~3.3× | ~33” | Easy; needs about 4 ft of counter for trays |
| 16×20 | ~4.7× | ~41” | Doable; big trays and ~6 ft of wet space |
| 20×24+ | ~5.7×+ | ~46”+ | A project; usually a rotated head projecting to the floor or wall |
The Brownie’s lens, not the film, limits sharpness at large sizes.
Buying notes
- Used 4x5 setup, all in: roughly $500–900 (enlarger, lens, carrier, easel, focuser).
- Shipping is the hidden cost. Prefer local pickup; a 45MX stands about 6 ft assembled.
- Before buying, confirm: the light source model and that it covers 4x5, lens focal length, which carriers are included, the baseboard, and that the column moves smoothly. Check that the condenser lenses are present and uncracked.
- Contact printing uses the same trays, chemistry, and safelight, so nothing bought for contact printing is wasted if enlarging comes later.