Room light Start here once the film is on the reel and the black lid is locked (loading the tank). Everything below happens at the sink in room light, and the lid stays on until the fixer is out. These steps are for HP5 Plus in Ilfosol-3. For the vintage 124 rolls, follow the vintage 124 rolls instead.
Equipment at the sink
- Loaded tank, plus the red cap
- Tub or sink of 68°F water as a temperature bath
- Thermometer
- 1000 mL beaker (working developer) and 100 mL graduate (concentrate)
- Bottle 1 (film fixer 1+4) and bottle 2 (stop 1+19)
- Ilfosol-3 concentrate
- RO/DI water, about 2 L
- Timer (a phone is fine because the film is sealed)
- Ilfotol and a 5 or 10 mL syringe
- Film clips (weighted + plain), notebook, paper towels
Step 1 — Temper (10–15 min)
- Fill the tub with 68°F (20°C) water.
- Stand the stop and fixer bottles, the loaded tank, and a jug of RO/DI mixing water in it.
- Get everything that touches the film to within 5°F of the developer. Big swings cause reticulation, a crazed pattern in the emulsion.
Step 2 — Mix
| Solution | 1 roll (600 mL) | 2 rolls (1000 mL) | Keep? |
|---|---|---|---|
| Developer Ilfosol-3 1+9 |
60 mL + 540 mL water | 100 mL + 900 mL water | No. One-shot, mix it last |
| Stop Ilfostop 1+19 (bottle 2) |
Pour 600 mL from bottle | Pour 1000 mL | Yes, until it turns purple |
| Fixer Rapid Fixer 1+4 (bottle 1) |
Pour 600 mL from bottle | Pour 1000 mL | Yes, about 24 rolls per liter |
Filling empty bottles: stop is 50 mL Ilfostop + 950 mL water into bottle 2. Fixer is 200 mL Rapid Fixer + 800 mL water into bottle 1. Label each one with the date and a roll tally.
Which water: mix all three solutions with RO/DI. Softened tap water would work, but it swaps calcium for sodium and its mineral content varies, while RO/DI gives the same result every time. Use softened tap water for the wash (Step 7) and RO/DI for the final rinse (Step 8). Draw the RO/DI ahead of time, because it usually comes out cold and needs to sit in the bath.
600 mL covers one 120 reel in the Multi-Reel 3 with margin. Check this once with water and an empty reel, then write the fill volume on the tank in Sharpie.
⚠ Fixer clip test — before every film roll
Bottle 1 fixes both film and prints, so check it’s still strong before you trust a roll to it.
- Pour a little fixer from bottle 1 into a cup at room temperature.
- Drop in a scrap of unprocessed film, such as a corner you trimmed while loading the reel. Developed film won’t work, because it has already been fixed. Light doesn’t matter for this test.
- Time how long the milky scrap takes to turn completely clear.
| Clear time | What to do |
|---|---|
| About 30 s | Fixer is good. Fix film for the normal 3 min, or twice the clear time if that’s longer. |
| About 60 s or more | Fixer is exhausted. Mix a fresh liter (200 mL concentrate + 800 mL water) before you develop. |
Pour the cup back into the bottle, or down the drain if it’s only a splash.
Step 3 — Set the time
Take the developer’s temperature right before you pour, then read off the time.
| 66°F | 67°F | 68°F | 69°F | 70°F | 72°F |
|---|---|---|---|---|---|
| 7:15 | 6:50 | 6:30 | 6:15 | 6:00 | 5:30 |
If the whole roll was shot in bright sun, take about a minute off (~5:30 at 68°F). Box cameras run HP5 about 2–3 stops over in sun.
HP5 at other speeds (Ilford box, 68°F)
| Shot at | Ilfosol-3 1+9 | Ilfosol-3 1+14 | Use |
|---|---|---|---|
| EI 200 | 5:00 | 7:00 | Bright sun in box cameras (overexposed roll) |
| EI 400 | 6:30 | 11:00 | Normal |
| EI 800 | 13:30 | 19:30 | Dim light, such as arenas (push 1 stop) |
| EI 1600+ | Not listed for Ilfosol-3. Use Ilfotec DD-X (1+4: 13:00 at 1600, 20:00 at 3200) | Pushing 2+ stops | |
Ilford’s box also gives ranges for stop (10–30 s) and fix (2–5 min), and calls for continuous agitation for the first 10 s, then 10 s every minute.
Other films in this recipe
| Film | Developer mix (600 mL) | Time at 68°F | Changes |
|---|---|---|---|
| Kodak Verichrome Pan 620/120, 1970s expired | Ilfosol-3 1+14: 40 mL + 560 mL RO/DI | 7:30 (confirmed on a good roll) | Fix 5 min. Extending to 12 min didn’t rescue a dead roll. Pink dye in the first wash is normal. |
Verichrome Pan is roughly Plus-X emulsion on a roll-film base, and it holds up well with age. Users report that decades-old rolls develop at about the normal time. Kodak never published an Ilfosol-3 time, so 7:30 at 1+14 is an estimate. The more dilute developer keeps the time above 5 minutes, below which Kodak warns development can be uneven. Write down what you get.
Verichrome log (Nov 2026)
| Roll | Result | Cause |
|---|---|---|
| 1 | Opaque gray, no edge print | Loaded under red safelight, which fogged the panchromatic film |
| 2, 3 | Cloudy, mottled gray. Edge print visible, no frames | Dead film: heavy age fog and almost no sensitivity left. The fog sits in the gaps and edges too, which rules out the camera. |
| 4 | Good images, clear gaps | Lamp-lit still life on B. About 1–2 s was best; 8 s and longer came out too dense. |
Old rolls vary by batch and by how they were stored. Note the date and lot number on each box, and match them to your results.
Step 4 — Develop
- Pull the red cap. Start the timer and pour the developer in steadily through the funnel. Cap it.
- First 30 s: slow, continuous inversions. Then tap the tank firmly on the counter to knock loose air bubbles.
- Top of every minute: 4 slow inversions (about 10 s), then tap. Between cycles, set the tank back in the bath.
- 10 s before the end: pull the cap and start pouring the developer out.
Keep inversions smooth and don’t shake. Shaking causes surge marks along the edges, and skipping the tap leaves bubble spots.
Step 5 — Stop (10 s)
- Pour in the stop and agitate continuously for 10 s.
- Pour it back into bottle 2.
Step 6 — Fix (3 min)
- Pour in the fixer. Agitate continuously for the first 30 s, then do 4 inversions each minute.
- At 3:00, pour it back into bottle 1. Squeeze the air out of the accordion bottle and add a tally mark.
- The film is now safe from light, so the lid can come off.
Step 7 — Wash (Ilford method, ~5 min)
Use softened tap water within 5°F of the developer, and dump each fill when you finish its inversions.
- Fill, 5 inversions, dump.
- Fill, 10 inversions, dump.
- Fill, 20 inversions, dump.
Step 8 — Final rinse (RO/DI, then Ilfotol)
-
RO/DI rinse: fill with RO/DI water, do a few gentle inversions, and dump. This clears the hard-water minerals left from the wash.
-
Mix the Ilfotol rinse (1+200) in the beaker. Use RO/DI water, and add the Ilfotol after the water so it doesn’t foam.
Rinse volume Ilfotol RO/DI water 600 mL (1 roll) 3 mL 597 mL 1000 mL (2 rolls) 5 mL 995 mL Stir gently. Bubbles mean you stirred too hard.
-
Soak, 30 s: pour it in and give it one or two very slow inversions, or just turn the reel by its center column. Vigorous agitation makes foam, and foam leaves marks.
-
Dump it. Use it once and drain it. Don’t rinse afterward. The thin layer of Ilfotol is what lets the water sheet off evenly.
-
Hang the film straight from the reel (Step 9). With Ilfotol, you can skip the finger squeegee or do it very lightly. Water runs off on its own.
Reel care: Ilfotol residue can make auto-load reels sticky. Rinse the reels well in warm water and dry them completely before the next load.
Step 9 — Hang to dry (2–3 h)
- Unwind the film from the reel, holding it by the edges.
- Clip the top in a dust-free spot (the shower stall with the door closed works), and hang a weighted clip on the bottom.
- Squeegee with your fingers only. A rubber squeegee drags grit across the emulsion.
- Leave it alone until it’s dry, then cut it into strips and sleeve it. From here on, every scratch and speck shows up in the print.
Step 10 — Clean up
| Item | What to do |
|---|---|
| Used developer | Down the drain with running water |
| Stop | Already back in bottle 2. Replace it when the indicator turns purple |
| Fixer | Already back in bottle 1. Clip-test it as you approach 24 rolls (chemistry lifespan). Never pour used fixer down the drain — it carries silver. Take exhausted fixer to household hazardous waste |
| Tank, lid, column, reels | Rinse in warm water. Dry the reels completely (overnight, or a hairdryer on cool) before the next load |
| Beaker, graduate, thermometer | Rinse. Developer residue stains, so wipe up spills now |
| Notebook | Record the film, camera, developer temperature, time, agitation, and anything odd |
Cheat card
Print this and tape it inside a cabinet door.
| Step | Solution | Time | After |
|---|---|---|---|
| Develop | Ilfosol-3 1+9, 68°F | 6:30 | Drain |
| Stop | Ilfostop 1+19 | 10 s | Bottle 2 |
| Fix | Rapid Fixer 1+4 | 3 min | Bottle 1 |
| Wash | Water, 5 / 10 / 20 inversions | ~5 min | Dump |
| Rinse | RO/DI, gentle inversions | ~30 s | Dump |
| Wetting agent | Ilfotol 1+200 in RO/DI (3 mL in 600 mL) | 30 s, 1–2 slow inversions | Drain, no rinse |
| Dry | Hang, weighted clip | 2–3 h | Sleeve |